Detection of sulfur dioxide at low parts-per-million concentrations using low-cost planar electrodes with ionic liquid electrolytes.

Sulfur dioxide (SO2) is a toxic gas at low parts-per-million (ppm) concentrations, with a permissible exposure limit (PEL) of 2 ppm. Its detection is mandatory, particularly in the fields of occupational health and safety, and environmental pollution. In this work, ppm concentration detection of sulfur dioxide was performed in six room temperature ionic liquids (RTILs), as well as on two different electrode materials - platinum and gold - and with two different electrode geometries, i.e. macro thin-film electrodes (TFEs) and microarray thin-film electrodes (MATFEs). Calibration curves were established for 10-200 ppm SO2 using cyclic voltammetry to determine the optimum combination of RTIL, electrode surface and geometry for the sensing. The RTIL 1-butyl-1-methylpyrrolidinium bis(trifluoromethylsulfonium)imide ([C4mpyrr][NTf2]) with a platinum thin-film electrode was found to give the best response due to the relatively low viscosity of the RTIL combined with the high sensitivity and a clean blank response. On MATFEs, deposited sulfur particles - confirmed using scanning electron microscopy (SEM) coupled to an energy dispersive spectrometer - were found to passivate and block some of the microholes, leading to unstable long-term chronoamperometric responses. To the best of our knowledge, this is the first observation of sulfur deposition from SO2 reduction in aprotic ionic liquids. Consecutive additions of 2 ppm SO2 were studied in [C4mpyrr][NTf2] on a TFE using long-term chronoamperometry, showing excellent reproducibility upon successive additions. This demonstrates that small volumes of RTILs can be combined with miniaturized, low-cost TFEs and applied for the reliable and continuous monitoring of sulfur dioxide gas at concentrations lower than the permissible exposure limit of 2 ppm.

Phase-Controllable Cobalt Phosphides Induced through Hydrogel for Higher Lithium Storages.

Transition metal phosphides (TMPs) have gained increased attention in energy storage due to their potential applications for optimizing electrochemical performances. However, their preparation routes usually require highly toxic and flammable phosphorus sources with strict reaction conditions. The existence of multiple energetically favorable stoichiometries also makes it a challenge to achieve phase control of metal phosphides. In this work, we have successfully realized the phase-controllable framework of cobalt phosphide from Co2P to CoP by employing a semi-interpenetrating network (semi-IPN) hydrogel as a precursor. Interestingly, the semi-IPN hydrogel could serve as a self-assembly/sacrificing template to accomplish 3D space confinement, where poly(vinylphosphonic acid) (PVPA) was identified as a prominent phosphorus source due to its strong metal complexation ability and high thermal stability. Furthermore, this route is successfully extended to the synthesis of other TMPs, including Fe2P, Ni2P, and Cu3P. The specific structure of cobalt phosphides gives rise to superior lithium storage performance, showing superior cycling stability (495.2 mAh g-1 after 1000 cycles at 2.0 A g-1). This approach envisions a new outlook on exploitation of essential functional hydrogels for the creation of inorganic materials toward sustainable energy development.

Thin films of poly(vinylidene fluoride-co-hexafluoropropylene)-ionic liquid mixtures as amperometric gas sensing materials for oxygen and ammonia.

Gas sensors are important devices used to monitor the type and amount of gas present. Amperometric gas sensors - based on measuring the current upon an applied potential - have been progressing towards miniaturised designs that are smaller, lower cost, faster responding and more robust compared to commercially available sensors. In this work, a planar thin-film electrode device is employed for gas sensing with a thin layer of gel polymer electrolyte (GPE). The GPE consists of a room temperature ionic liquid (RTIL, with two different imidazolium cations and the tetrafluoroborate [BF4]- anion) mixed with poly(vinylidene fluoride-co-hexafluoropropylene) (PVDF-HFP). The polymer acts as a scaffold, with the RTIL ions able to flow within the porous percolated channels, resulting in a highly robust gel with high conductivity. The chemical nature of the polymer allows thin-films (ca. 6 µm) to be evenly dropcast onto planar electrode devices, using minimal amounts of material. Remarkably, no significant effect of resistance was observed in the voltammetric response with such thin films. Oxygen (O2) and ammonia (NH3) gases were detected in the concentration ranges 1-20% O2 and 1-10 ppm NH3 in the two GPEs using both linear sweep voltammetry (LSV) and long-term chronoamperometry (LTCA). LTCA was the preferred detection method for both gases due to the steady-state current response compared to the sloping current response from LSV. The thin nature of the film gave fast response times for both gases - less than 10 seconds for O2 and ca. 40 seconds for NH3 - easily rivaling the commercially available porous electrode designs and allowing for continuous monitoring of gas concentrations. These materials appear to be highly promising candidates as gas detection electrolytes in miniaturised devices, with accurate and fast responses in both the cathodic and anodic potential regions.

Ionophore-Assisted Electrochemistry of Neutral Molecules: Oxidation of Hydrogen in an Ionic Liquid Electrolyte.

The electrochemical properties of gas molecules are of great interest for both fundamental and applied research. In this study, we introduce a novel concept to systematically alter the electrochemical behavior and, in particular, the redox potential of neutral gas molecules. The concept is based on the use of an ion-binding agent, or "ionophore", to bind and stabilize the ionic electrochemical reaction product. We demonstrate that the ionophore-assisted electrochemical oxidation of hydrogen in a room-temperature ionic liquid electrolyte is shifted by almost 1 V toward more negative potentials in comparison to an ionophore-free electrolyte. The altered electrochemical response in the presence of the ionophore not only yields insights into the reaction mechanism but also can be used to determine the diffusion coefficient of the ionophore species. This ionophore-modulated electrochemistry of neutral gas molecules opens up new avenues for the development of highly selective electrochemical sensors.

Formation of 3-Dimensional Gold, Copper and Palladium Microelectrode Arrays for Enhanced Electrochemical Sensing Applications.

Microelectrodes offer higher current density and lower ohmic drop due to increased radial diffusion. They are beneficial for electroanalytical applications, particularly for the detection of analytes at trace concentrations. Microelectrodes can be fabricated as arrays to improve the current response, but are presently only commercially available with gold or platinum electrode surfaces, thus limiting the sensing of analytes that are more electroactive on other surfaces. In this work, gold (Au), copper (Cu), and palladium (Pd) are electrodeposited at two different potentials into the recessed holes of commercial microelectrode arrays to produce 3-dimensional (3D) spiky, dendritic or coral-like structures. The rough fractal structures that are produced afford enhanced electroactive surface area and increased radial diffusion due to the 3D nature, which drastically improves the sensitivity. 2,4,6-trinitrotoluene (TNT), carbon dioxide gas (CO2), and hydrogen gas (H2) were chosen as model analytes in room temperature ionic liquid solvents, to demonstrate improvements in the sensitivity of the modified microelectrode arrays, and, in some cases (e.g., for CO2 and H2), enhancements in the electrocatalytic ability. With the deposition of different materials, we have demonstrated enhanced sensitivity and electrocatalytic behaviour towards the chosen analytes.

Molten metal closo-borate solvates.

Solvated lithium closo-dodecaborate, Li2B12H12 with tetrahydrofuran and acetonitrile, show unexpected melting below 150 °C. This feature has been explored to melt-infiltrate Li2B12H12 in a nanoporous SiO2 scaffold. The ionic conductivity of Li2B12H12·xACN reaches 0.08 mS cm-1 in the liquid state at 150 °C making them suitable as battery electrolytes.

Screen-Printed Graphite Electrodes as Low-Cost Devices for Oxygen Gas Detection in Room-Temperature Ionic Liquids.

Screen-printed graphite electrodes (SPGEs) have been used for the first time as platforms to detect oxygen gas in room-temperature ionic liquids (RTILs). Up until now, carbon-based SPEs have shown inferior behaviour compared to platinum and gold SPEs for gas sensing with RTIL solvents. The electrochemical reduction of oxygen (O2) in a range of RTILs has therefore been explored on home-made SPGEs, and is compared to the behaviour on commercially-available carbon SPEs (C-SPEs). Six common RTILs are initially employed for O2 detection using cyclic voltammetry (CV), and two RTILs ([C2mim][NTf2] and [C4mim][PF6]) chosen for further detailed analytical studies. Long-term chronoamperometry (LTCA) was also performed to test the ability of the sensor surface for real-time gas monitoring. Both CV and LTCA gave linear calibration graphs-for CV in the 10-100% vol. range, and for LTCA in the 0.1-20% vol. range-on the SPGE. The responses on the SPGE were far superior to the commercial C-SPEs; more instability in the electrochemical responses were observed on the C-SPEs, together with some breaking-up or dissolution of the electrode surface materials. This study highlights that not all screen-printed ink formulations are compatible with RTIL solvents for longer-term electrochemical experiments, and that the choice of RTIL is also important. Overall, the low-cost SPGEs appear to be promising platforms for the detection of O2, particularly in [C4mim][PF6].

Detection of 2,4,6-Trinitrotoluene Using a Miniaturized, Disposable Electrochemical Sensor with an Ionic Liquid Gel-Polymer Electrolyte Film.

A new electrochemical method to detect and quantify the explosive compound 2,4,6-trinitrotoluene (TNT) in aqueous solutions is demonstrated. A disposable thin-film electrode modified with a droplet of a gel-polymer electrolyte (GPE) was immersed directly into samples of TNT at concentrations of 1-10 µg/mL. The GPE contained the hydrophobic room-temperature ionic liquid (RTIL) trihexyltetradecylphosphonium bis(trifluoromethylsulfonyl)imide ([P14,6,6,6][NTf2]) and the polymer poly(hexyl methacrylate). The RTIL acted to preconcentrate TNT into the GPE and provided ionic conductivity. The polymer provided both (i) sufficient viscosity to ensure mechanical stability of the GPE and (ii) strong hydrophobicity to minimize leaching of the RTIL. Square wave voltammetry was performed on the first reduction peak of TNT-preconcentrated samples (15 min soaking with mechanical stirring), with linear plots of peak current vs cumulative concentration of TNT, giving an averaged limit of detection of 0.37 µg/mL (aqueous phase concentration). Additionally, the voltammetry of the first reduction peak of TNT in [P14,6,6,6][NTf2] was unaffected by the presence of oxygen-in contrast to that observed in an imidazolium-based RTIL-providing excellent selectivity over oxygen in real environments. The sensor device was able to quickly and easily quantify TNT concentrations at typical ground water contamination levels. The low-cost and portability of the sensor device, along with the minimal amounts of GPE materials required, make this a viable platform for the onsite monitoring of explosives, which is currently a significant operational challenge.

Achievement of Prolonged Oxygen Detection in Room-Temperature Ionic Liquids on Mechanically Polished Platinum Screen-Printed Electrodes.

The demonstration of prolonged amperometric detection of oxygen in room-temperature ionic liquids (RTILs) was achieved by the use of mechanical polishing to activate platinum screen-printed electrodes (Pt-SPEs). The RTILs studied were 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide ([C2mim][NTf2]) and N-butyl-N-methyl-pyrrolidinium bis(trifluoromethylsulfonyl)imide ([C4mpyrr][NTf2]). It was found that voltammetry on polished Pt-SPEs exhibited less deterioration (in terms of voltammogram shapes, stability of peak currents, and appearance of contaminant peaks) from long-term consecutive cycling under 100% vol oxygen flow in both RTILs. The detection capability of these RTIL/Pt-SPE systems, initially subjected to long-term consecutive voltammetric cycling, was also investigated by cyclic voltammetry (CV) and long-term chronoamperometry (LTCA). Current versus concentration plots were linear on both unpolished and polished electrodes for 10-100% vol O2 (using CV) and 0.1-5% vol O2 (using LTCA). However, sensitivities and limits of detection (LODs) from CV were found to improve significantly on polished electrodes compared to unpolished electrodes, particularly in [C2mim][NTf2], but also moderately in [C4mpyrr][NTf2]. The lowest LODs (of ca. 0.1% vol O2) were found on polished SPEs using LTCA, with the most stable responses observed in [C4mpyrr][NTf2]. Calibration graphs could not be obtained on unpolished electrodes in both RTILs using LTCA. The results show that polishing markedly improves the analytical performances of Pt-SPEs for oxygen sensing in RTILs. The reusability of such disposable Pt-SPEs, after the surfaces had been experimentally fouled, was also demonstrated through the use of polishing. Mechanical polishing of Pt-SPE devices offers a viable approach to performance improvement for amperometric gas sensing.

Low-cost microarray thin-film electrodes with ionic liquid gel-polymer electrolytes for miniaturised oxygen sensing.

A robust, miniaturised electrochemical gas sensor for oxygen (O2) has been constructed using a commercially available Pt microarray thin-film electrode (MATFE) with a gellified electrolyte containing the room temperature ionic liquid (RTIL) 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide ([C2mim][NTf2]) and poly(methyl methacrylate) (PMMA) in a 50 : 50 mass ratio. Diffusion coefficients and solubilities for oxygen in mixtures of PMMA/RTIL at different PMMA doping concentrations (0-50% mass) were derived from potential step chronoamperometry (PSCA) on a Pt microdisk electrode. The MATFE was then used with both the neat RTIL and 50% (by mass) PMMA/RTIL gel, to study the analytical behavior over a wide concentration range (0.1 to 100 vol% O2). Cyclic voltammetry (CV) and long-term chronoamperometry (LTCA) techniques were employed and it was determined that the gentler CV technique is better at higher O2 concentrations (above 60 vol%), but LTCA is more reliable and accurate at lower concentrations (especially below 0.5% O2). In particular, there was much less potential shifting (from the unstable Pt quasi-reference electrode) evident in the 50% PMMA/RTIL gel than in the neat RTIL, making this a much more suitable electrolyte for long-term continuous oxygen monitoring. The mass production and low-cost of the electrode array, along with the minimal amounts of RTIL/PMMA required, make this a viable sensing device for oxygen detection on a bulk scale in a wide range of environmental conditions.

Evidence for a surface confined ion-to-electron transduction reaction in solid-contact ion-selective electrodes based on poly(3-octylthiophene).

The ion-to-electron transduction reaction mechanism at the buried interface of the electrosynthesized poly(3-octylthiophene) (POT) solid-contact (SC) ion-selective electrode (ISE) polymeric membrane has been studied using synchrotron radiation-X-ray photoelectron spectroscopy (SR-XPS), near edge X-ray absorption fine structure (NEXAFS), and electrochemical impedance spectroscopy (EIS)/neutron reflectometry (NR). The tetrakis[3,5-bis(triflouromethyl)phenyl]borate (TFPB(-)) membrane dopant in the polymer ISE was transferred from the polymeric membrane to the outer surface layer of the SC on oxidation of POT but did not migrate further into the oxidized POT SC. The TFPB(-) and oxidized POT species could only be detected at the outer surface layer (≤14 Ǻ) of the SC material, even after oxidation of the electropolymerized POT SC for an hour at high anodic potential demonstrating that the ion-to-electron transduction reaction is a surface confined process. Accordingly, this study provides the first direct structural evidence of ion-to-electron transduction in the electropolymerized POT SC ISE by proving TFPB(-) transport from the polymeric ISE membrane to the oxidized POT SC at the buried interface of the SC ISE. It is inferred that the performance of the POT SC ISE is independent of the thickness of the POT SC but is instead contingent on the POT SC surface reactivity and/or electrical capacitance of the POT SC. In particular, the results suggest that the electropolymerized POT conducting polymer may spontaneously form a mixed surface/bulk oxidation state, which may explain the unusually high potential stability of the resulting ISE. It is anticipated that this new understanding of ion-to-electron transduction with electropolymerized POT SC ISEs will enable the development of new and improved devices with enhanced analytical performance attributes.

Is ballistic transportation or quantum confinement responsible for changes in the electrical properties of thin polymer films?

Resistivities of thin polymer films increase abruptly with decreasing thickness, although the corresponding decline in resistance plateaus below a certain thickness. One can jump to the incorrect conclusion that quantum confinement and surface scattering are responsible for this behaviour, and we highlight the pitfalls of committing such an error.